Manometers MP KIMO MP -K: from to °C -J: from to °C -T: from to °C CO/Temperature: CO: from 0 to ppm, from Consult KIMO’s MP brochure on DirectIndustry. Page: 1/4. This is the MP Thermo-Anemo-Manometer. It is an easy to use meter which can take complex measurements. The MP is designed to measure Air.

Author: Nezilkree Yozshugar
Country: Bahamas
Language: English (Spanish)
Genre: Education
Published (Last): 10 June 2017
Pages: 116
PDF File Size: 17.91 Mb
ePub File Size: 16.37 Mb
ISBN: 320-4-59204-550-2
Downloads: 67640
Price: Free* [*Free Regsitration Required]
Uploader: JoJogal

Click on Esc to return to previous screen. It’s a community-based project which helps to repair anything. For measurement launching, click on OK with the access key. To save your dataset click on Save with the access key. With Pressure function, you can access to following sub-functions – Hold – see Air velocity – Config. Select compensation It is possible to modify the value of the compensation in temperature.

Launch a planned dataset A planned dataset is composed of several locations. Press 1x in order to select HOLD function: Summary screen of selected dataset is displayed.

If you click on average icon, max. On enabled mode, the probe is connected, the measurement is carried out and the value is displayed.

Use the arrows to modifiy the threshold value then press Validate to validate alarm threshold and back to measurement screen. If you want to see all values, select Visu. When the countdown is finished, the CO max is displayed.

Select Start for dataset launching.

The numbers of points is displayed. From this screen, press Measure to back to measurement. Wire probes with Smart-plus system Wire probes with Smart-plus system are automatically recognized when connected to the instrument. Probe Hold Alarms Params Veloci.


KIMO MP manometer buy in Kamenskoe

Preview of tables of points of datasets Dataset summary You can display tables of points of datasets performed on the device. Alarm threshold corresponds to the right value on the bargraph. For each kkimo, the operator can enter a theorical value and a tolerance for the parameter kiom be controlled.

If K factor is selected, you must enter value. Configuration If you use thermocouple probes, you must enter type into the Configuration sub-function.

Click on Mesure to display values table of selected dataset. In regards of Quality insurance norms, we recommend that the instruments are checked once a year. The number of points selected and the parameter are displayed. The beep repetition frequency will increase accordong to the increase of detected gas concentration, and the display will blink at the same frequency.

Configuration – Params Parameters – Avg. When the solenoid valve is enabled, kp runs every minute.

Press Ok for launching measurement. From this screen you can: If the probe has been just connected, the screen indicates the remaining time of warm up then the measurement screen appears, indicates kkmo concentration and places it on a bargraph. Enter dataset time and interval of time between 2 measurements by selecting Period with access key.

Kimo MP H MPH Thermo-Anemo-Manometer

Air velocity with Pitot tube: Create or launch a continuous dataset Select dataset A continuous dataset can kiom carried out using MP and is composed of several dated measuring points. Kumo can access this function selecting COmax with the access key CO max The CO is measured on an adjustable period, the maximum value measured in this period is called CO max. Battery When battery indicator flashes it is recommended to change the batteries: Several actions are possible during the measurement: Planification must be made via the software.


Press 2x in order to select Min-Max function: When CO peak is selected, the period is diplayed 30 seconds by default. Memory capacity of the instrument is up to 8, points or 50 datasets.

Kkmo function can also be automatically performed by using the solenoid valve function.

To modify the period, press Period with the access key. Remove the front part at the back of the instrument. From kim screen, you can: You must enter duration: If Other is selected, you must enter a value.

Kimo MP200 Multi Function Manometers

When the measurement is fixed, press Min Max to access to maximum and minimum values of the measurement. Average – Rec Recording Veloci. If the probe is connected for more than 1 minute, measurement screen appears and indicates the concentration and places it on a bargraph.

Author: admin