Documents Similar To CINI Manual. Industrial Insulation Manual. Uploaded by. Haris Prawoto. Standard Specification for Hot Insulation (Piping & Equipment). This SPECIFICATION is based on the CINI Handbook “Insulation for Industries”, English. Version, dated 1st October (also known as the ” edition”). This section is based on the Committee Insulation Netherlands. Industry (CINI) Manual “Insulation for Industries”. DACE fol- lows the CINI standard as much as.
|Published (Last):||26 October 2005|
|PDF File Size:||5.76 Mb|
|ePub File Size:||9.80 Mb|
|Price:||Free* [*Free Regsitration Required]|
All insulation products shall. Typical removable covers for spectacle blind flanges in vertical and horizontal pipes are shown in Appendices 10 and In many More janual. A minimum of two layers of cellular glass shall be applied. They support petrochemical plant, More information. The adhesives shall withstand any stresses and strains, accommodate contraction within the foam and remain effective within the required temperature range.
All carbon steel parts shall be hot dip galvanised. Our expert More information.
Cini :: CINI manual CD rom
Manul upon the service application the design, construction, inspection, More information. Lnsulation responsibility of the engineer is. What is Static Electricity? The potential cost and safety implications are enormous, and therefore insulation systems shall be designed according to categories that indicate vulnerability to CUI and are related to the process temperatures. Dip tank operations involving flammable More information. Dip tank operations involving flammable. TICP and shall be subject industriez the approval of the Principal.
Pressure vessel basics for all engineers Pressure vessel basics for all engineers by Sharjeel Aslam Faiz 1. Valves, flanges and nozzles shall be insulated, unless other requirements are overruling, e. For flammable products, insulation collars of Cellular Glass shall be applied near flanges in order to prevent product from entering the insulation system. In both hot, cold and cryogenic services.
In the plant construction or process plants such as chemical, petrochemical, gas or power plants various disciplines are brought into contact and built on each other. Each line should be insulated separately; a common insulation cover should not enclose adjacent lines.
High quality inrustries insulation. To make this website work, we log user data and share it with processors. Pipe and Equipment Insulations. Part IV specifies requirements and gives recommendations for inspection and maintenance of existing insulation systems that are not covered in the CINI Handbook.
CINI – International Standard for Industrial Insulation
Alternatives shall be submitted to the Principal for approval and shall be supported by references e. Section includes, but is not limited to, design and furnishing portable davits, davit sleeves, dvit bases, four 4 removable outriggers. Protective fencing or perforated jacketing may be considered for personnel protection. Drainage outlets should be provided to give visible indication of possible valve or flange leakage. The changes mentioned in the other parts have been implemented. The use of mobile manufacturing facilities e.
This aluminium foil will act as both a barrier coat and inhibitor. If metal jacketing is used, sufficient space and drainage shall be provided to avoid internal accumulation of water caused by condensation, water vapour diffusion, capillary action and water ingress.
Pouring shall only be allowed for emergency maintenance, if injection equipment is not directly available. Over the last years of model boiler making the only real change in construction methods has been the change over from rivets and caulking. For inspection an ITP Inspection Test Plan shall be submitted, which indicates all phases for test and inspections of the insulation systems.
The following table indicates vulnerabilities to CUI: Civil, mechanical, electro technical More information. General Vaporizers are constructed in numerous designs and operated in many modes. The annular space between insulation material and bare surface is a non-ventilated space in which openings or drains are always located at the lowest point of the piping or equipment.
All metal surfaces under insulation shall be suitably protected with a complete paint system in accordance with DEP Gen. Supply and install all materials and accoutrements required for the installation. Roof coverings More information.
However, the applicable material specifications and the numerous construction details, obtained from different disciplines and years of experience, form a good basis for a proper insulation specification.
All materials and application methods shall be selected to suit local weather and environmental conditions.
The placing of the pre-formed spacers will insulafion on the location of supports, welds, auxiliaries, etc. Part V lists the publications referenced in this DEP. LNG loading lines Injection Application methods a and b The foam injection process shall be in accordance with the recommendations of the Manufacturer.
VDIor other standards if specified by the Principal, shall be used to calculate the contribution of convection. Spacers shall be fastened securely by means of stainless steel bands, filament tape or glue.
CINI Manual Industrial Technical Insulation
The method for calculating the economic thickness of insulation shall be in accordance with Section 1. The maximum stresses in the foam shall be limited to 0. For smaller pipe diameters metal jacketing is not recommended.
The software shall comply with the information given in CINI and related standards.