epD‐BfS‐ () Environmental Product  Schweizerischer ingenieur‐ und Architektenverein (SiA). () Merkblatt energieausweis für Gebäude gemäß Sn en und Sn en zurich.  Schweizerischer . Flash point: > 21° C „Beschichtung auf Zink und verzinktem Stahl“ from Bundesausschuss Farbe und Sachwertschutz (BFS) according to Merkblatt 5 of BFS. Flash point: > 21° C. Solid substance: approx. 55% Zinc and galvanized surfaces are to be prepared according to Merkblatt 5 of. BFS. Clean the surfaces to be painted and remove dirt of all kinds, including dust, mortar droppings, and similar.
|Published (Last):||7 September 2014|
|PDF File Size:||1.91 Mb|
|ePub File Size:||3.67 Mb|
|Price:||Free* [*Free Regsitration Required]|
Mechanical loads scratching on matt facade paints in dark shades may produce bright-toned stripes as a product specific property no writing resistance. In case of contact with 2 or skin, immediately and thoroughly rinse with water. Maximum temperature for high-pressure water jet: By eliminating the need to sample alternative paths for estimation, it also simplifies the estimation process, making it a merkblath choice as an integral solution for joint route and mode choice modelling.
If swallowed, seek medical advice immediately and show the container or label intestinal bacteria can be affected. The results indicated that proximity to social contacts was an important factor and that it was traded off against commute time.
Transport Planning – Theory and Models. This project, consisting of a main and an extension study, estimated models for the prediction of the impacts of changes in parking supply fbs daily travel behavior for different trip purposes and spatial contexts. Facades in special climatic conditions high degree of bfss or subjected to a higher influence of atmospheric exposure: Allow merkblattt dry thoroughly.
Weathered spray and scratch renders: Fast-drying after rainfall and when moist with dew. Harmful to aquatic life with long lasting effects. Constant exposure to splashing water is detrimental to the durability of coatings. Using a joint model including all relevant choice situations, this paper investigates the difference in the valuation of time coming from different kind of choice experiments.
In case of direct reworking, all traces of additives must be pre-wetted and completely removed after a short reaction time. On roughly textured surfaces correspondingly more. Clean soiled or chalking coatings with high-pressure water jet, in compliance with the regulations.
Widen structural cracks approx.
May produce an allergic reaction. PermaSilan NQG is provided with a preservative against deterioration in the coating film due to algae and fungal attack. If swallowed, seek medical advice immediately and show the container or label intestinal bacteria can be affected. The traces cannot occur when the paint is applied under suitable climatic conditions. Prime slightly absorbent or smooth surfaces with AmphiSilan-Grundierfarbe.
Permeable to CO 2 Resistant to aggressive air pollutants. Suitability according to Technical Information No. Thus this paper demonstrates the need for refinement of the definition of such a VTT.
Use P2 dust filter for grinding. Fill with Cap-elast Riss-Spachtel and allow to dry thoroughly. Bridging Treatment Reinforced with Polyester Fabric.
Surface Coating System Remove fungal or algal attack by wet-blasting, in compliance with the regulations. Keep out of reach of children. Repair small defects with fine filler Caparol Fassaden-Feinspachtel, deeper defects up to 20 mm preferably with Histolith-Renovierspachtel and prime repairs subsequently. Clean existing renders by suitable wet cleaning method. Keep out of reach from children. An additional priming coat of CapaGrund Universal must be applied.
Elastic even at low temperatures.
A recursive logit approach. Adverse weather conditions, e. Harmful to aquatic life with long lasting effects.
Keep out of reach of children.
ThermoSan NQG: Caparol
Material Properties Water-dilutable, ecologically compatible, low odour. If brownish discolouration appears on the intermediate coat, apply the anhydrous, solvent-based facade paint Duparol for finishing coat. In case of moist weather conditions rain, dew, fog yellowish transparent traces mrrkblatt additives, showing a mermblatt glossy shine and stickiness, may occur on the surface of compact, cool substrates or by means of delayed drying caused by the weather.
Apply one priming coat of AmphiSilan-Putzfestiger. Clean utensils immediately after use with soap and water. In case of direct reworking, all traces of additives must be pre-wetted and completely removed after a short reaction time. Depending on atmospheric humidity, temperature and layer thickness. It is therefore advisable to apply a first coat in a similar hiding pastel tint, based on white. Highly CO 2 permeable. Prime the repaired areas. Remove unstable, weathered, poorly adherent coats of mineral paint sand off, abrade or cauterise and rinse the full meekblatt thoroughly.
This product contains max. Allow wet cleaned surfaces to dry thoroughly before any further treatment. Each additional application with a consumption of min.
Static cracks are liable to extreme movements. Do not eat, drink or smoke while using the nfs.